- Ge Universal Remote Model 33709 User Manual
- Ge 33709 Remote Code List
- Ge Universal Remote 33709 User Manual System
- Ge Universal Remote 33709 Setup
- 33709 Ge Remote Control Manual
Four digit codes for GE Universal remote controls
Direct Code Entry for GE remotes with 4 digit codes
Ge Universal Remote Model 33709 User Manual
The following is a short tutorial on programming most models of GE universal remotes with 4 digit codes. See also this page for general GE remote code entering instructions.
Step 1: Press and hold the 'SETUP' button until the indicator light turns on, then release.
Samsung Galaxy S10 manual is needed in order to guide you so that you can use it better. In this site also include how to setup the phone, tips, tricks and troubleshooting information. Download the user guide for Galaxy S10, S10e and S10+ here. Download Official Samsung Galaxy S10 Manual and User Guide PDF. Galaxy S10e Galaxy S10: Galaxy S10+ Assemble your device: Start using your device 3: Galaxy S10e: Gettingstarted 4. Use only charging devices and batteries that are approved by Samsung. Samsung charging devices and batteries are designed for your device to maximize battery life. Using other charging devices and batteries may void your. Nov 08, 2019 Samsung Galaxy S10e manual user guide is a pdf file to discuss ways manuals for the Samsung Galaxy S10e.In this document are contains instructions and explanations on everything from setting up the device for the first time for users who still didn’t understand about basic function of.
Step 2: Press and release the desired Mode button (TV, DVD, CBL/SAT, etc.). The indicator light will blink, then stays lit.
Step 3: Enter the 4 digit code for your device. After a valid code entry, the indicator light turns off. For an invalid code, the indicator light flashes.
Step 4: With your device on, test a few common functions like 'CHANNEL Up/Down' or 'VOLUME Up/Down' , 'MUTE', etc. If the device responds, no further programming is required. If some buttons don't work as they should, try a different code listed for your brand.
NOTE: The indicator light will either be a small red LED at the top of the remote or the illuminated 'ON/OFF' button.
Ge 33709 Remote Code List
About codes used in GE/Jasco remotes
There were multiple 4 digit code versions used in GE remotes over time, from V1 (2006), V2 (2011), V3, V4 (2012), V5, CL3 (2013), CL4 (2016) to the newest CL5 (2019).
To find out the version your remote uses, open the battery compartment, remove the batteries and locate the sticker containing the model number. A Version 2 through Version 5 remote will have a 'V2' to 'V5' after the model number. Older remotes with no version after the model# use the V1 code list. The newest ones will be CL3, CL4 or CL5.
Search Manuals; Universal Remote Codes; Autosys. Ge 33709 remote codes. Ge 33709 remote codes direct Code Entry for GE remotes with 4 digit codes. Enter the three or four digit code for your device using the number buttons in the GE Universal Remote. After your code is entered the INDICATOR LIGHT will turn off. Aim the remote at the.
In order to save you the hassle of going through multiple code tables, we have compiled together the code lists from different versions of GE remotes sharing the same code base (e.g. V2&V4, V3&V5). If your remote is slightly old, you'll get the benefit of finding the code for your device even if it appeared after your remote was manufactured, but uses an old code that already exists preprogrammed in your model. You can also find the code for some old devices that are dropped from the code lists, but still supported by newer remote controls. The only downside of this approach is, that there will be a few codes that are only supported by a particular version. So, if a code listed for your brand is not supported by your remote, try the next one from the list.
Sometimes a code will be accepted, but only allow limited function control (e.g. only volume and channel control). In this case, continue programming using the next code number for that brand.
Auto Code Search
The Auto Code Search searches automatically through all of the codes stored in your remote. If your device does not respond to any of the codes listed for your device, or your brand does not appear in the code lists, try the following steps:
Step 1: Manually turn on the device you wish to control.
Step 2: Press and hold the 'SETUP' button until the red indicator light stays on (around 4 seconds) and then release the button.
Step 3: Press and release the desired device button on the remote (TV, DVD, CBL/SAT, DVR/AUX). The red indicator will blink once and remains on.
Ge Universal Remote 33709 User Manual System
Step 4: Point the remote at the device and press and release the 'POWER' button (for TV) or 'PLAY' button (for DVD, VCR, etc.) to start the search. The red indicator will flash (approximately every 2 seconds) as the remote searches. The remote must be pointed at your device for the entire duration of this search.
Step 5: Place your finger on the #1 button so you are prepared to lock-in the code.
Step 6: When the device shuts off or begins playing, press the #1 button to lock-in the code. The red indicator light will turn off. Note: You have approximately two seconds after the device shuts off or begins playing to lock-in the code.
Step 7: Point the remote at your device and check to see if the remote operates it as desired. If it does, no further programming is required. If it does not, return to step 2 and start the auto search again.
Code Search instructions for some older GE remotes
Step 1: Manually turn on the device to be controlled.
In, a decision tree describes data (but the resulting classification tree can be an input for ). Classification and regression trees cart a user manual for identifying. This page deals with decision trees in.
Step 2: Press and hold the 'SETUP' button until the red indicator stays on, then release.
Step 3: Press and release the desired Mode button (VCR, TV etc.). The red indicator will blink once, then stays on.
Step 4: Press the 'POWER' (or 'CHANNEL UP' for some versions) button repeatedly until the device to be controlled powers off (or changes channel). The red indicator will blink with each keypress. When all codes have been searched the red indicator flashes rapidly for 3 seconds.
Ge Universal Remote 33709 Setup
Step 5: Press and release 'ENTER' (or 'MUTE' or 'SAVE') button to install the code. The indicator light goes off.
33709 Ge Remote Control Manual
Generally it's best to store VCR codes under the VCR button, cable codes under CBL, and so on. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter any VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.